# Switching from "EZ Blocky" to raspberry pi OS bookworm (32)

**URL:** <https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955>\
**Category:** General\
**Created:** [March 30, 2025, 9:01pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955 "2025-03-30T21:01:10Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![danfagerburg](https://avatars.discourse-cdn.com/v4/letter/d/a88e4f/32.png) [@danfagerburg](https://forum.sunfounder.com/u/danfagerburg)\
**Post date:** [March 30, 2025, 9:01pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/1 "2025-03-30T21:01:10Z")

</div>

I assembled my Picar-X by creating the disk image of “EZ Blocky” instead of installing Bookworm 32; I also installed the RPi V-2 camera.

When I finished, the calibrations And Everything did not respond in “EZ Blocky”, and after studying EZ Blocky, I realized I should have stuck to python inside Bookworm 32.

Given my Picar-X is fully assembled (properly, with the servos zero’ed) How do I get it to run off a different microSD? Is it OK to have the hat plugged in, as well as the 3 servos and sensors when I install the necessary packages?

Please help,

---

<div class="post-metadata">

**Author:** ![SunFounder\_Moderator](https://avatars.discourse-cdn.com/v4/letter/s/34f0e0/32.png) [@SunFounder\_Moderator](https://forum.sunfounder.com/u/SunFounder_Moderator)\
**Post date:** [March 31, 2025, 10:14am UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/2 "2025-03-31T10:14:20Z")

</div>

It is recommended that you prepare two SD cards, one for Python control and one for ezblock control.  
If you use Python in Bookworm 32 to do servo zeroing and calibration, normally, you do not need to do zeroing and calibration when you switch to ezblock, so you can just use the running example.  
It is recommended that you connect all hardware modules when installing the software.

---

<div class="post-metadata">

**Author:** ![danfagerburg](https://avatars.discourse-cdn.com/v4/letter/d/a88e4f/32.png) [@danfagerburg](https://forum.sunfounder.com/u/danfagerburg)\
**Post date:** [March 31, 2025, 4:03pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/3 "2025-03-31T16:03:32Z")

</div>

But if the initial installation of the Picar-X was with EX Block image, do I install the RPi OS with the robot-hat and sensors/motors plugged in?

---

<div class="post-metadata">

**Author:** ![danfagerburg](https://avatars.discourse-cdn.com/v4/letter/d/a88e4f/32.png) [@danfagerburg](https://forum.sunfounder.com/u/danfagerburg)\
**Post date:** [March 31, 2025, 6:16pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/4 "2025-03-31T18:16:23Z")

</div>

But if the initial installation of the Picar-X was with EX Block image, do I install the RPi OS with the robot-hat and sensors/motors plugged in?

---

<div class="post-metadata">

**Author:** ![SunFounder\_Moderator](https://avatars.discourse-cdn.com/v4/letter/s/34f0e0/32.png) [@SunFounder\_Moderator](https://forum.sunfounder.com/u/SunFounder_Moderator)\
**Post date:** [April 1, 2025, 6:46am UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/5 "2025-04-01T06:46:55Z")

</div>

If you used the EX Block image when you initially installed Picar-X, you will need to connect the robot hat when you install the RPi OS because you want to verify that the robot hat’s speakers are working properly.

---

<div class="post-metadata">

**Author:** ![danfagerburg](https://avatars.discourse-cdn.com/v4/letter/d/a88e4f/32.png) [@danfagerburg](https://forum.sunfounder.com/u/danfagerburg)\
**Post date:** [April 1, 2025, 2:04pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/6 "2025-04-01T14:04:43Z")

</div>

Can you please tell me how to configure the dependencies and programs if the car is Pre-assembled. When I first tried, the Only thing that works is the speaker, none of the motors…

---

<div class="post-metadata">

**Author:** ![danfagerburg](https://avatars.discourse-cdn.com/v4/letter/d/a88e4f/32.png) [@danfagerburg](https://forum.sunfounder.com/u/danfagerburg)\
**Post date:** [April 1, 2025, 8:20pm UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/7 "2025-04-01T20:20:50Z")

</div>

After assembling the robot car, Picar-x, the speaker works great- but None of the sensors or motors are responsive. How do I proceed to troubleshoot?

---

<div class="post-metadata">

**Author:** ![SunFounder\_Moderator](https://avatars.discourse-cdn.com/v4/letter/s/34f0e0/32.png) [@SunFounder\_Moderator](https://forum.sunfounder.com/u/SunFounder_Moderator)\
**Post date:** [April 2, 2025, 8:08am UTC](https://forum.sunfounder.com/t/switching-from-ez-blocky-to-raspberry-pi-os-bookworm-32/2955/8 "2025-04-02T08:08:41Z")

</div>

- If you’re using **EZBlock** , you’ll need to connect to **PiCar-X** either through the EZBlock app or web interface, then run the corresponding block or example program to activate movement.
- If you’re working with **Python** , please ensure you execute the provided example code (refer to the attached image for reference) to initiate the actions.  
 ![screenshot_2025-04-02_16-05-01](https://canada1.discourse-cdn.com/flex029/uploads/sunfounder/original/2X/3/3f460b0c80739564b97791022a529cf0b5301a71.png)
